CARA PENGGUNAAN
G1 - STARTER RING
G2 - BODY RING
G3 - SWIM SEAT

Swimava Starter Ring Instructions – Step by Step:

1. Inflate the Swimava Starter Ring

- Insert the pump nozzle firmly into the top air chamber safety valve to break the factory seal. Be careful not to damage the air valve.

- Pump up the top chamber until it is full and feels firm. Next repeat steps with the bottom chamber. If the seams begin to show strain stop inflation and release air to reduce pressure until all signs of stress on the seams are gone. (See Fig. 1 &2)

- Ensure each valve is securely plugged after being filled. Regularly check the valves to ensure they are plugged.

- Do not over inflate the ring.

- Prior to each use of the Starter Ring Put the ring completely under water for 60 seconds and check for any air bubbles indicating leakage.

- The small air pump is not a toy, keep it out of reach of children.

Inflate:

Use the pump to inflate, then push valve down firmly to close

Deflate:

Squeeze valve to release air

2. Place the Swimava Starter Ring on your infant

- Caregiver #1 should support the infant’s head while Caregiver #2 fastens the Starter Ring. Open the Starter Ring and gently bring it around the infant’s neck from the front or from behind. The infant handles should be on the bottom and facing down. (See Fig. 3)

- Close the Starter Ring securing both the top and bottom buckles. Gently lift the infant’s chin before fastening.

- Always adjust the Starter Ring diameter to suit your infant prior to placing him in the pool or bath.

- You should always be able to slide at least 2 fingers in between the Starter Ring and your infant all the way around. Watch closely for signs of distress or discomfort. (See Fig 4)

- You can slightly decrease the lower/inner air chamber pressure to relax the inner ring diameter if the ring feels too tight.

- The upper air chamber should always be fully inflated.

- The Starter Ring should freely move around the infant’s neck and should only be supporting the head above the water.

3. Test the Water Temperature and Adjust the Water Level

- Fill the Swimava Bath or your bath tub with warm water.

- Adjust the water level so your infant can float and enjoy free movement of his arms and legs in the water while the Swimava Starter Ring acts as a gentle support keeping the head above water. (See Fig. 5)

- The water temperature should be approximately 34 degrees Celsius (93 degrees Fahrenheit) with no more than +/- 2 degrees Celsius (+/- 3,6 degrees Fahreinheit) variation. Monitor the water temperature with a floating baby thermometer.

4. Place your Infant in the Water

- Support your infant from under the arms while gently placing him in the bath or pool.

- Never leave an infant unattended while using this Swimava Starter Ring or any floatation product. Always remain within arm’s reach.

- Never Use the infant handles on the Starter ring to lift your infant in or out of the water.

- Do not use bath oils in the water as these can affect the durability of the plastic PVC Swimava Starter Ring. This could also make surfaces unexpectedly slippery and lead to an accident when removing your infant from the water.

- Pay close attention to your infant for signs he is ready to finish bath/swim time. Your infant most certainly will let you know when he has had enough

- Although it may be possible for you infant to enjoy the Swimava Starter Ring for over 20 minutes per session, this should not be exceeded.

5. Take your Infant out of the Water

- Two caregivers should always be present when taking your infant out of the water.

- Caregiver #1 should hold the infant firmly under the arms while lifting the infant out of the water. Caregiver #2 should slowly remove the Swimava Starter Ring. (See Fig.6)

Swimava Starter Ring Instructions – Step by Step:

1. Inflate the Swimava Starter Ring

- Insert the pump nozzle firmly into the top air chamber safety valve to break the factory seal. Be careful not to damage the air valve.

- Pump up the top chamber until it is full and feels firm. Next repeat steps with the bottom chamber. If the seams begin to show strain stop inflation and release air to reduce pressure until all signs of stress on the seams are gone. (See Fig. 1 &2)

- Ensure each valve is securely plugged after being filled. Regularly check the valves to ensure they are plugged.

- Do not over inflate the ring.

- Prior to each use of the Starter Ring Put the ring completely under water for 60 seconds and check for any air bubbles indicating leakage.

- The small air pump is not a toy, keep it out of reach of children.

Inflate:

Use the pump to inflate, then push valve down firmly to close

Deflate:

Squeeze valve to release air

2. Place the Swimava Starter Ring on your infant

- Caregiver #1 should support the infant’s head while Caregiver #2 fastens the Starter Ring. Open the Starter Ring and gently bring it around the infant’s neck from the front or from behind. The infant handles should be on the bottom and facing down. (See Fig. 3)

- Close the Starter Ring securing both the top and bottom buckles. Gently lift the infant’s chin before fastening.

- Always adjust the Starter Ring diameter to suit your infant prior to placing him in the pool or bath.

- You should always be able to slide at least 2 fingers in between the Starter Ring and your infant all the way around. Watch closely for signs of distress or discomfort. (See Fig 4)

- You can slightly decrease the lower/inner air chamber pressure to relax the inner ring diameter if the ring feels too tight.

- The upper air chamber should always be fully inflated.

- The Starter Ring should freely move around the infant’s neck and should only be supporting the head above the water.

3. Test the Water Temperature and Adjust the Water Level

- Fill the Swimava Bath or your bath tub with warm water.

- Adjust the water level so your infant can float and enjoy free movement of his arms and legs in the water while the Swimava Starter Ring acts as a gentle support keeping the head above water. (See Fig. 5)

- The water temperature should be approximately 34 degrees Celsius (93 degrees Fahrenheit) with no more than +/- 2 degrees Celsius (+/- 3,6 degrees Fahreinheit) variation. Monitor the water temperature with a floating baby thermometer.

4. Place your Infant in the Water

- Support your infant from under the arms while gently placing him in the bath or pool.

- Never leave an infant unattended while using this Swimava Starter Ring or any floatation product. Always remain within arm’s reach.

- Never Use the infant handles on the Starter ring to lift your infant in or out of the water.

- Do not use bath oils in the water as these can affect the durability of the plastic PVC Swimava Starter Ring. This could also make surfaces unexpectedly slippery and lead to an accident when removing your infant from the water.

- Pay close attention to your infant for signs he is ready to finish bath/swim time. Your infant most certainly will let you know when he has had enough

- Although it may be possible for you infant to enjoy the Swimava Starter Ring for over 20 minutes per session, this should not be exceeded.

5. Take your Infant out of the Water

- Two caregivers should always be present when taking your infant out of the water.

- Caregiver #1 should hold the infant firmly under the arms while lifting the infant out of the water. Caregiver #2 should slowly remove the Swimava Starter Ring.


P1 - DELUXE HOME SPA POOL
Ini adalah Produk Tipe Tube 5-tahap.

Produk ini dapat menyesuaikan ketinggiannya dengan hanya menempatkan udara sesuai kebutuhan, dan ini adalah kolam serbaguna yang dapat dipasang dengan stabil meskipun air tidak terisi.

Konstruksi Tabung Kuat.

Udara dipompakan masuk ke masing-masing tabung 5 tahap dengan menggunakan pompa udara untuk penggunaan kolam secara eksklusif, yang merupakan komponen dasarnya.

Utilisasi Luas.

Karena berat struktur tubular dan material yang tebal, produk ini tidak akan ambruk meskipun tanpa diisi air.

Design Illustrasi Kapal Berlayar Bergaya America.

Menampilkan desaign illustrasi perahu mewah.


P2 - COMPACT BABY HOME SPA
Penempatan di ruang kecil pun OK!

instalasi mudah Baby Swim Moments untuk mengamati Bayi Lebih Dekat.

Instalasi Mudah.

Anda bisa menggunakannya hanya dengan memasukkan tulang penopang di sekeliling produk.

Struktur Drainase yang Mudah.

Drainase dengan jenis katup penutup disediakan, dan mudah untuk mengeluarkan air setelah digunakan.

 

Ilustrasi Populer Karakter bayi bebek asli Swimava digambar di bagian luar kolam, membuatnya lebih imut.

 

Kedalaman adalah faktor terpenting untuk proses berenang yang ideal bagi bayi Anda. Jika kedalaman air dangkal, posisi bayi akan menjadi tidak nyaman. Semakin dalam air, semakin bebas pergerakan tubuh. Kolam renang spa kompak Swimava bisa menampung lebih dari 200 liter air.


P3 - LE MACARON BABY HOME SPA
Akun Saya
Layanan Pelanggan
Informasi Umum
Pertanyaan Bisnis
P. +62 812 188 188 62
BELANJA LAGI
Cek produk lainnya di ORENJIBABY.COM ORENJIBABY.COM
email. info@swimava.id phone. (021) 225 701 91, 0812 188 188 62